Legend Suspensions

We want to thank all of our customers for your continued support throughout 2025. Wishing you a great holiday season. Order processing and customer service may be delayed from December 19th through January 5th.

MY LEGEND

SIGN IN

0
0
Subtotal: $0.00 USD

No products in the cart.

Return To Shop
legend suspensions logo
 

Fitment: 1999 - 2024 Harley-Davidson FLH Touring Models

P3002-REV C

Parts: 1310-0936, 1310-0937, 1310-0938, 1310-0939,1310-0958, 1310-0959, 1310-0960, 1310-0961, 1310-1617, 1310-1618, 1310-1740, 1310-1741,1310-1774, 1310-1775, 1310-1779, 1310-1780

INSTALL INSTRUCTIONS

STEP ONE: INSTALL SHOCKS

  1. With motorcycle properly supported on jack, remove the stock shocks.
  2. Apply blue threadlocker to the hardware and install your REVO shocks FIGURE A. If installing REVO-A, install with adjuster knob facing the rear of the motorcycle.
  3. Torque hardware to 50 ft-lbs.

WARNING:
Before purchasing or attempting to install shocks that are different than the OEM length, confirm that the wheel travel can be altered without causing clearance issues, such as swing-arm/axle to  exhaust contact as well as chain/belt guard and tire clearance.

FIGURE A
  1. Legend supplied large spacer
  2. Legend supplied small spacer
  3. OE lock washer
  4. OE bolt
  5. Rebound adjuster facing rear of motorcycle

STEP TWO: CHECK FOR PROPER MOUNTING

Once shocks are installed with the proper hardware FIGURE A, make sure you can rotate them freely in both directions FIGURE B.

IF SHOCKS DO NOT ROTATE FREELY, CHECK THAT THE HARDWARE IS INSTALLED CORRECTLY.

  1. Do not use large OEM flat washers
FIGURE B

SET UP INSTRUCTIONS

STEP ONE: SET SAG

  1. Verify springs on each shock are adjusted evenly (same
    number of threads exposed below the spring) FIGURE D.
  2. Sit rider (with gear on), passenger, and the load you intend
    on carrying, on the motorcycle.
  3. Measure the shock length from the center of the lower
    mounting bolt to the center of the upper mounting bolt
    FIGURE C.
  4. Refer to the table below to determine the proper sag
    measurement based on the shock length purchased:
Shock Length Proper Sag Measurement
12" 11.5"
13" 12"
  1. If the measured length is less than the proper sag measurement.
    Increase spring preload by threading spring UP the shock body
    to tighten spring (LESS SAG) FIGURE D.
  2. If the measured length is greater than the proper sag measurement.
    Decrease spring preload by threading spring DOWN the shock body
    to tighten spring (MORE SAG) FIGURE D.
  3. Make equal adjustments to left and right shocks.
FIGURE C

STEP TWO: REBOUND DAMPING (APPLICABLE TO REVO-A)

  1. Rebound damping controls the speed at which the shock absorber
    extends after being compressed.
  2. If you feel the suspension has a mushy or oscillating feel to it, increase
    the rebound damping to a higher number. If the suspension feels slow
    reacting or feels firm on closly spaced bumps, decrease the rebound
    damping to lower number.
  3. Turn rebound adjuster to the same number on the left and right shocks,
    firmer or softer depending on preference and test ride again.
  1. Fine tune rebound damping: For Legend Air-A and Revo-A models. Machined recess below rebound adjuster indicates rebound setting.
  2. Setting 1: provides lowest level of rebound damping.
  3. Setting 3: provides intermediate level of rebound damping. IMPORTANT: most commonly used setting
  4. Setting 6: provides highest level of rebound damping.
  5. Machined recess on shock
FIGURE D
  1. Increase Spring Preload
  2. Reduce Spring Preload
  3. Before adjusting sag, verify this measurement is the same on both sides.
Privacy Settings